Klevaklip Concealed Fixing Systems & Building Hardware Supplier Sydney Australia

 

klevaklip-sydney-supplier

 

Klevaklip Systems Pty Ltd is an Australian owned company originally set-up to provided concealed fixing systems for decking materials. Over a period of time, the company has diversified to provide products that may fill niche markets in the building industry.  

Trex Snap-Loc Clips

Patent Pending

trex-snaploc-klevaklip Klevaklip has developed a new concealed fixing system to suit the Trex Decking Boards. This new system is called the Snap-Loc Clips.

Klevaklips new clip for the Trex Transcend decking range, manufactured from Nylon 6 engineering polymer, is two to three times faster to install than conventional “biscuit-type” decking clips. For the decking contractor this means you can quickly get the job finished and move onto the next job, whilst for the DIY-er, your time to sit back and enjoy your first beer on the deck is ever so closer.

This product is recommended to be used for square or rectangular shaped decks only.  

Klevaklip Modwood Clips

Australian Patent NOS 2007278768

klevaklip-modwood-sydney

Klevaklip Modwood concelead fixing clips were developed in conjunction with Modwood. The Klevaklips are the preferred method of fixing for Modwood decking boards. 

KlevaKlip is a multi-board concealed fixing system that provides consistent gapping of the boards. As each Modwood board is inserted into the KlevaKlip, it tightens the previous board, providing significant holding power of the board into the clever clip. This holding is supported by the use of an adhesive to provide a look, longevity and feel that is difficult to obtain with conventional fastening systems.

 

Klevaklip Building Hardware

KlevaKlip has released a range of purpose-built building products designed to make the building of these low-lying decks faster, easier and less hassles.

 

Klevaklip-adjustable-joist-supportThe Adjustable Joist Support

The Adjustable Joist Support has been designed specifically to enable decks to easily be built over concrete slabs in areas where limited ground clearance is available. It is ideal for use when the step-down from your door to your concrete slab is between 100mm (minimum) and around 260mm (maximum).

Why use the Klevaklip Adjustable Joist Support? 

  • Keeps your joists off the concrete and free of unwanted moisture ingress.This prevents joist-rot through the bottom of joists.
  • Is ideal for use on area where the concrete has built in "fall" - to provide a level deck.
  • Quick and easy to use – purpose-built for the application
  • Gives a neat, professional look across your deck structure without  resorting to various different packers and   brackets to achieve your end result. 
  • Uses standard 10mm hex head bolts, nuts and washers and 12mm dynabolts or 10mm masonry bolts.  

 

 

The Adjustable Bearer Support - for decks approx. 300mm to 600mm off the groundklevaklip-adjustable-bearer-support

Every deck starts with the process of getting the substructure right - if it isn't properly spaced out and level, the chances of building the deck correctly are almost zero.

Therefore time must be spent on getting the posts or piers set to the correct height across the deck - a job made even more difficult if the ground is not level. 

The clever people from KlevaKlip have introduced the Adjustable Bearer Support.

Extremely easy-to-use, and suited for decks up to approximately 600m off the ground, the Adjustable Bearer Support allows you to be much less critical with your height measurements in the knowledge that you can simply wind the bearer support up or down to set your perfect height.

It will save lots of time and make your job so much easier. 

 

 

klevaklip-joist-connectorThe Joist Connector for attaching 45mm wide joists to 45mm, 70mm or 90mm Bearers

The range of KlevaKlip Joist Connectors have revolutionised the way joists are attached to bearers.

An absolute must for every handyman and quickly becoming the preferred fixing method of many builders, the

Joist Connector makes the set-out and fixing off of your substructure a breeze.

 

 

 

The FREP Joist Hanger (Fibre Reinforced Engineering Polymer) - suits 90x45mm & 140x45mm Joistsklevaklip-joist-hanger

Finally there is a reasonably priced, corrosion-proof joist hanger on the market.

The new FREP Joist Hanger (Fibre Reinforced Engineering Polymer) is strong- engineered to last, light weight, easy to use, has no sharp edges, and will not corrode in any environment.

NJH9045 suits 90x45mm Joists upwards

NJH14045 suits 140x45mm Joists upwards

 

 

 

klevaklip-sydney-supplier